User | Pavlok | Text |
 |
| But the other thing I do not get is that it kept intermittently flashing both red and light the entire night |
| 
| The possible reason could be that it is not paired with the app or the battery is low. Please also observe if you are still getting the same light pattern after turning off the hand detection feature. |
User | Pavlok | Text |
|
| There is an intermittent vibration with both red and green light flashing |
| 
| Thank you for reaching out. Could you please check if the hand detection feature is on? |
 |
| Yes Active Ok so I will just disactivate it I guess
|
| 
| Yes, it should be turned off if you are not using it, as it activates a vibe whenever your hand is near your face. |
Red, Yellow, Blinking Light Meaning for Pavlok and Shock Clock Devices
Shock Clock 3 and Pavlok 3
Generation 3 Devices feature a set of LEDs above the buttons.
These lights report various conditions and events.
Below are the most important indicators:
---
Soft Reset Worked:
Soft Reset Procedure:
Plug in the USB charging cable.
Press the middle button for 10 seconds.
Indicators:
All lights turn on: Green (constant), Yellow and Red (flashing) for 3 seconds with continuous vibration then a flashing yellow light from bottom to top.
Meaning:
Soft Reset worked.
Encryption keys are removed.
iOS devices may need fo Forget Device to reconnect.
---
iOS Pairing Problem:
Indicators:
Single Green flash.
Two Yellow flashes.
Single Red flash.
or
Two all-yellow flashes followed
Three Red flashes
Meaning:
Bluetooth pairing issue with iOS.
Solution:
Go to Bluetooth menu in iOS Settings.
Tap the 'i' icon next to your device.
Select "Forget Device" and re-pair.
---
Low Battery:
Indicators:
Red LED flashes three times periodically.
Meaning:
Battery level is low.
Solution:
Recharge soon.
---
Clock not set:
Indicators:
Two quick double flashes of the Red LED.
Followed by a long Red flash.
Meaning:
Clock is not set.
Solution:
Reconnect with the app to restore clock and alarms.
---
Snap:
Indicators:
Red LED: Snap is charging.
Yellow LEDs: Animate during snap.
Green LED: Flashes if charge was successfully delivered.
Note:
If Green LED doesn't flash, adjust position or tighten wristband.
---
Shock Clock 2 and Pavlok 2
"I'm trying to charge my Pavlok 2 and the battery blinks red twice, then a 2 second red light then dim to bright yellow light and then repeats these steps. Any idea what's going on? "
That pattern blinks when the device has been completely depleted of battery - it just shows that it needs to be paired with the app again to re-sync with the time zone.
Wed. Mar. 8 2023 11:19 a.m. EST
Button Info:
Lightning Bolt Button:
Snooze: 1 press (5-minute duration).
Turn off Alarm: Hold for 5 seconds.
Indicators:
Blink Red every 15 seconds
Meaning:
Device is In Snooze Mode
Charging:
Procedure:
Charge via the Micro-USB port using the included USB cord.
Plug one end into the Shock Clock, the other into a computer's USB port or USB wall charger.
Indicators:
Red pulse: Charging.
Solid Yellow: Fully charged.
The Green LED at the top will be lit up. (Gen 3 Only)
if you plug in the device and it is fully charged.
Note from Deon Don:
Hey there! This quick read was whipped up by yours truly, Deon Don, over at Pavlok Research.
Got questions or wanna suggest some cool features?
Shoot me a text at (731) 472-8565.
Don't sweat it if I don't hit you back right away – I'll definitely circle back to you after I've had a chance to check my messages.
And yes, I read every single one.